CDL Combination Vehicles Sample Questions and Explanations
No published past questions are available for this exam yet. Instead, here are 10 of our 134 AI-written CDL Combination Vehicles practice questions, chosen to match the question types that come up most.
The CDL Combination Vehicles exam covers CDL Combination Vehicles Test (20), 20 questions in total. New to 'combination vehicles test'? Read these first to see what to expect.
'Reviewed' means a separate AI that could not see the answer solved the question again and its answer matched. 'Not yet reviewed' means that check has not been done yet. No human expert has checked these questions, so use 'Report a problem' on the practice screen if something looks wrong.
CDL Combination Vehicles: 10 sample questions
Question 1. Before coupling, how should the fifth wheel be positioned?
- ① Tilted up toward the cab, jaws closed, safety latch off
- ② Tilted down toward the rear of the tractor, jaws open, safety unlocking handle in the automatic lock position
- ③ Level, jaws closed, release handle pulled out
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ② Tilted down toward the rear of the tractor, jaws open, safety unlocking handle in the automatic lock position
Key point: Coupling position: tilted down to rear, jaws open
Check that the fifth wheel is in the right position for coupling: wheel tilted down toward the rear of the tractor, jaws open, and the safety unlocking handle in the automatic lock position. A sliding fifth wheel must be locked.
Wrong choices
- Tilted up toward the cab, jaws closed, safety latch off: Tilted up with jaws closed is the wrong position.
- Level, jaws closed, release handle pulled out: Closed jaws cannot accept the kingpin.
Question 2. After coupling, how much space should there be between the upper and lower fifth wheel?
- ① About one inch
- ② No space
- ③ About two inches
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ② No space
Key point: No space between upper and lower fifth wheel
There should be no space between the upper and lower fifth wheel. If there is space, something is wrong.
Wrong choices
- About one inch: Any space means a problem.
- About two inches: Two inches is a sign of a bad coupling.
Question 3. What two things does the manual say help most to prevent a combination vehicle from rolling over?
- ① Inflate the trailer tires above normal and brake hard before curves
- ② Keep the cargo as low as possible and drive slowly around turns
- ③ Load the heaviest cargo at the top and keep a steady speed in turns
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ② Keep the cargo as low as possible and drive slowly around turns
Key point: Rollover prevention: low cargo + slow turns
A high load raises the center of gravity, so the rig tips more easily. The two main defenses are keeping cargo close to the ground and driving slowly around turns. Keeping the load centered also helps.
Wrong choices
- Inflate the trailer tires above normal and brake hard before curves: Overinflating tires and hard braking in curves do not lower the rollover risk; slowing before the curve does.
- Load the heaviest cargo at the top and keep a steady speed in turns: Heavy cargo on top raises the center of gravity and makes a rollover more likely.
Question 4. You make a quick lane change while pulling a trailer. What dangerous effect can tip the trailer over?
- ① Hydroplaning
- ② Brake fade
- ③ The crack-the-whip effect
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ③ The crack-the-whip effect
Key point: Quick lane change → crack-the-whip can flip the trailer
Trucks with trailers have a crack-the-whip effect: a sudden steering move is magnified at the trailer, which can turn the trailer over even when the tractor stays upright.
Wrong choices
- Hydroplaning: Hydroplaning is loss of tire contact on water; it is not what flips a trailer in a lane change.
- Brake fade: Brake fade comes from overheated brakes, not from a lane change.
Question 5. When should you use the trailer hand valve?
- ① Only to test the trailer brakes
- ② To slow down on every downgrade
- ③ To hold the rig when parked
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① Only to test the trailer brakes
Key point: Trailer hand valve: for testing only
Use the trailer hand valve only to test the trailer brakes. Do not use it while driving because it can make the trailer skid, and never use it for parking.
Wrong choices
- To slow down on every downgrade: Using it while driving risks a trailer skid; use the foot brake.
- To hold the rig when parked: Air can leak away, so it cannot be trusted for parking.
Question 6. What is the main job of the tractor protection valve?
- ① To keep air in the tractor brake system if the trailer breaks away or has a bad leak
- ② To keep the trailer from rolling backward on hills
- ③ To limit how much air goes to the steering axle
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① To keep air in the tractor brake system if the trailer breaks away or has a bad leak
Key point: Tractor protection valve saves the tractor's air
The tractor protection valve keeps air in the tractor or truck brake system should the trailer break away or develop a bad leak.
Wrong choices
- To keep the trailer from rolling backward on hills: That is not its job; parking and emergency brakes hold the trailer.
- To limit how much air goes to the steering axle: It protects the tractor's air from trailer leaks, not the steering axle.
Question 7. Trailers and converter dollies built on or after what date must have antilock brakes (ABS)?
- ① January 1, 1975
- ② March 1, 2008
- ③ March 1, 1998
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ③ March 1, 1998
Key point: Trailers/dollies built on or after March 1, 1998 need ABS
All trailers and converter dollies built on or after March 1, 1998, are required to have ABS. Many older ones were also equipped with ABS by choice.
Wrong choices
- January 1, 1975: 1975 is the date tied to spring brakes on trailers, not ABS.
- March 1, 2008: 2008 is ten years too late.
Question 8. What is the main benefit of ABS during hard braking?
- ① It lets you follow other vehicles more closely
- ② It helps you keep the vehicle under control
- ③ It always makes the stopping distance much shorter
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ② It helps you keep the vehicle under control
Key point: ABS helps control, not always shorter stops
ABS does not necessarily shorten your stopping distance, but it helps you keep the vehicle under control during hard braking.
Wrong choices
- It lets you follow other vehicles more closely: ABS does not allow closer following.
- It always makes the stopping distance much shorter: The manual says ABS does not necessarily shorten stopping distance.
Question 9. During the walk-around, what should you see between the upper and lower fifth wheel?
- ① No visible space
- ② A small gap for air flow
- ③ A layer of rubber padding
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① No visible space
Key point: Inspection: no visible space at the fifth wheel
When checking the lower fifth wheel, look for no visible space between the upper and lower fifth wheel, enough grease, no missing parts, and jaws around the shank.
Wrong choices
- A small gap for air flow: A gap is a warning sign, not a design feature.
- A layer of rubber padding: There is no rubber pad between the plates.
Question 10. During the walk-around, what should be true of the landing gear?
- ① Lowered slightly so it can support the trailer in a stop
- ② Removed if the trailer is loaded
- ③ Fully raised, with no missing parts, not bent, and the crank handle secured
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ③ Fully raised, with no missing parts, not bent, and the crank handle secured
Key point: Landing gear: fully up, undamaged, crank secured
The landing gear should be fully raised, with no missing parts, not bent or damaged, and the crank handle in place and secured. If it is power-operated, there should be no air or hydraulic leaks.
Wrong choices
- Lowered slightly so it can support the trailer in a stop: It must be fully raised for driving.
- Removed if the trailer is loaded: The landing gear is part of the trailer and stays on.
Practice the other 124 questions
Instant answers and explanations. Free, no login.