CDL Combination Vehicles: Inspecting a Combination Vehicle Concepts
Importance ★★★★☆ · 10% (estimate)
Based on 2026 exam standards
Overview
A combination is inspected with the same seven-step method as any commercial vehicle, plus checks for parts a single truck does not have. This chapter lists those extra walk-around items and explains the four brake tests for a combination, which apply to doubles and triples too.
On the walk-around you look at both halves of the coupling, the air hoses and electrical cord, any sliding fifth wheel, and the landing gear. Most items ask whether a part is secure, undamaged, greased, or fully raised, and whether hoses have enough slack for turns.
The brake tests prove that air reaches the back of the rig, that the tractor protection valve closes on its own when pressure falls, and that both the trailer emergency brakes and service brakes work. Each test uses a different control, and questions often swap one test's method into another.
Key concepts
Air-to-all-trailers test
With normal pressure and the red knob pushed in, you go to the very back and open the emergency valve, then the service valve with the brakes applied, listening for air from each. If no air comes out, first check that the shut-off valves on the trailers and dollies are open.
Memory tipHear air at the back, then close the valves.
Tractor protection valve test
With the system charged and the engine off, you press and release the brake pedal several times to lower the pressure. The trailer air supply knob should pop out in the range the maker sets, usually 20 to 45 psi.
Memory tipEngine off, fan the pedal, watch the knob.
Source: New York State DMV, CDL-10 Section 6 (AAMVA model manual) · as of 2025
Trailer emergency brake test
After checking that the charged trailer rolls freely, you pull out the trailer air supply knob and tug gently with the tractor to feel the trailer brakes hold.
Memory tipKnob out, gentle tug.
Trailer service brake test
With normal pressure and the parking brakes released, you roll forward slowly and apply the trailer brakes with the hand valve, if there is one. In normal driving the foot pedal controls them.
Memory tipHand valve to test, pedal to drive.
Sliding fifth wheel
A fifth wheel that can move along the frame. Its locking pins must all be present and locked, and it must not sit so far forward that the frame hits the landing gear or the cab hits the trailer in a turn.
Memory tipPins in, not too far forward.
Inspecting a Combination Vehicle: key points
- Lower fifth wheel: secure, greased, no visible space, jaws on the shank, release arm and latch set
- Upper fifth wheel: glide plate tight to the trailer frame, kingpin not damaged
- Sliding fifth wheel: all locking pins in place; not so far forward that the frame hits the landing gear
- Air reaches all trailers: open the valves at the rear of the last trailer and listen for air
- Tractor protection valve test: engine off, fan the pedal; knob pops out at about 20 to 45 psi
- Trailer emergency brakes: pull the knob, then tug gently
- Trailer service brakes: roll slowly and apply the hand valve; drive with the foot pedal
Inspecting a Combination Vehicle: common mistakes
Common mistake: To test the trailer emergency brakes, I apply the trailer hand valve while rolling slowly.
What is correct: Rolling slowly and using the hand valve is the service brake test. For the emergency brakes, check that the trailer rolls freely, then pull out the trailer air supply control and pull gently to feel them hold.
Common mistake: If no air comes out at the back of the last trailer, the tractor protection valve must be bad.
What is correct: The first thing to check is the shut-off valves on the trailers and dollies; they must be open so air reaches the back.
Common mistake: During the tractor protection valve test, I keep the engine running.
What is correct: Shut the engine off first. With it running, the compressor keeps refilling the tanks, so the pressure never falls far enough for the knob to pop out.
Inspecting a Combination Vehicle: 10 sample questions
Question 1. During the walk-around, what should you see between the upper and lower fifth wheel?
- ① No visible space
- ② A small gap for air flow
- ③ A layer of rubber padding
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① No visible space
Key point: Inspection: no visible space at the fifth wheel
When checking the lower fifth wheel, look for no visible space between the upper and lower fifth wheel, enough grease, no missing parts, and jaws around the shank.
Wrong choices
- A small gap for air flow: A gap is a warning sign, not a design feature.
- A layer of rubber padding: There is no rubber pad between the plates.
Question 2. During the walk-around, what should be true of the landing gear?
- ① Lowered slightly so it can support the trailer in a stop
- ② Removed if the trailer is loaded
- ③ Fully raised, with no missing parts, not bent, and the crank handle secured
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ③ Fully raised, with no missing parts, not bent, and the crank handle secured
Key point: Landing gear: fully up, undamaged, crank secured
The landing gear should be fully raised, with no missing parts, not bent or damaged, and the crank handle in place and secured. If it is power-operated, there should be no air or hydraulic leaks.
Wrong choices
- Lowered slightly so it can support the trailer in a stop: It must be fully raised for driving.
- Removed if the trailer is loaded: The landing gear is part of the trailer and stays on.
Question 3. To check that air flows all the way back, where do you open the emergency line shut-off valve?
- ① At the tractor protection valve
- ② At the front of the first trailer
- ③ At the rear of the last trailer
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ③ At the rear of the last trailer
Key point: Open the emergency-line valve at the rear of the last trailer
Go to the rear of the rig and open the emergency line shut-off valve at the rear of the last trailer. You should hear air escaping, which shows the whole system is charged. Then close it.
Wrong choices
- At the tractor protection valve: The tractor protection valve is in the tractor, not at the rear.
- At the front of the first trailer: Opening at the front would not show that air reaches the back.
Question 4. You open the valves at the rear of the last trailer but hear no air from either line. What should you check?
- ① That the landing gear is raised
- ② That the ABS lamp is on
- ③ That the shut-off valves on the trailers and dollies are in the open position
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ③ That the shut-off valves on the trailers and dollies are in the open position
Key point: No air at the rear: check shut-off valves are open
If you do not hear air escaping from both lines, check that the shut-off valves on the trailer(s) and dolly(ies) are in the OPEN position. You must have air all the way to the back for all the brakes to work.
Wrong choices
- That the landing gear is raised: The landing gear does not affect the air lines.
- That the ABS lamp is on: The ABS lamp has nothing to do with air flow.
Question 5. When testing the tractor protection valve, within what pressure range does the air supply knob usually pop out?
- ① 20 to 45 psi
- ② 100 to 125 psi
- ③ 60 to 80 psi
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① 20 to 45 psi
Key point: Knob usually pops out at 20–45 psi
The knob should pop out within the manufacturer's range, usually 20 to 45 psi.
Wrong choices
- 100 to 125 psi: That is a normal operating pressure.
- 60 to 80 psi: 60 psi is about where the low-air warning comes on.
Question 6. How do you test the trailer emergency brakes?
- ① Charge the system, check the trailer rolls freely, pull out the air supply control, and pull gently to feel the brakes hold
- ② Look at the brake lights from behind the trailer
- ③ Press the foot brake hard at highway speed
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① Charge the system, check the trailer rolls freely, pull out the air supply control, and pull gently to feel the brakes hold
Key point: Emergency brake test: pull the knob, tug gently
Charge the trailer air brake system and check that the trailer rolls freely. Then stop, pull out the trailer air supply control (or set it to "emergency"), and pull gently on the trailer with the tractor to check that the trailer emergency brakes are on.
Wrong choices
- Look at the brake lights from behind the trailer: Brake lights do not show whether the brakes hold.
- Press the foot brake hard at highway speed: That tests the service brakes, and not safely.
Question 7. How do you test the trailer service brakes?
- ① Pull out the trailer air supply knob while parked
- ② With normal air pressure and parking brakes released, move forward slowly and apply the trailer brakes with the hand control
- ③ Drain the trailer tanks and listen
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ② With normal air pressure and parking brakes released, move forward slowly and apply the trailer brakes with the hand control
Key point: Service brake test: roll slowly, apply with the hand valve
Check for normal air pressure, release the parking brakes, move the vehicle forward slowly, and apply the trailer brakes with the hand control (trolley valve), if the rig has one. You should feel the brakes come on.
Wrong choices
- Pull out the trailer air supply knob while parked: Pulling the knob tests the emergency brakes, not the service brakes.
- Drain the trailer tanks and listen: Draining the tanks does not test the service brakes.
Question 8. During the walk-around, the lower fifth wheel locking jaws are closed around the head of the kingpin instead of the shank. What does this mean?
- ① This is normal for a loaded trailer
- ② The coupling is not right and the rig should not be driven
- ③ This is normal if the safety latch is on
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ② The coupling is not right and the rig should not be driven
Key point: Jaws on the head, not the shank = bad coupling
The jaws must be around the shank, not the head, of the kingpin. Jaws on the head mean a bad coupling; do not drive until it is fixed.
Wrong choices
- This is normal for a loaded trailer: Load does not change where the jaws should be.
- This is normal if the safety latch is on: The safety latch does not make a bad jaw position safe.
Question 9. How do you test the tractor protection valve?
- ① Charge the system, shut off the engine, and step on and off the brake pedal several times; the air supply knob should pop out within the set range
- ② Pull out the air supply knob at full pressure and listen for a click
- ③ Drain the tractor tanks completely with the engine running
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① Charge the system, shut off the engine, and step on and off the brake pedal several times; the air supply knob should pop out within the set range
Key point: Tractor protection valve test: fan the pedal; knob should pop
Build up normal pressure and push the air supply knob in. Shut the engine off and step on and off the brake pedal several times to lower the tank pressure. The trailer air supply control should pop out (or go to "emergency") when the pressure falls into the range set by the manufacturer.
Wrong choices
- Pull out the air supply knob at full pressure and listen for a click: Pulling the knob by hand does not show that it closes by itself.
- Drain the tractor tanks completely with the engine running: With the engine running, the compressor keeps refilling the tanks.
Question 10. After testing the trailer service brakes with the hand valve, how should you control the trailer brakes in normal driving?
- ① With the foot pedal, which applies air to the service brakes at all wheels
- ② With the hand valve, so you can brake the trailer separately
- ③ With the trailer air supply knob
▼ Show answer and explanation▲ Hide answer and explanation
Answer: ① With the foot pedal, which applies air to the service brakes at all wheels
Key point: Test with the hand valve; drive with the foot pedal
The trailer brakes should be tested with the hand valve but controlled in normal operation with the foot pedal, which applies air to the service brakes at all wheels.
Wrong choices
- With the hand valve, so you can brake the trailer separately: Using the hand valve while driving can make the trailer skid.
- With the trailer air supply knob: The knob is for supplying air and setting the trailer emergency brakes, not normal braking.
Test yourself.
- Importance
- ★★★★☆ (4 / 5)
- Weight
- About 2 of 20 CDL Combination Vehicles Test questions (10%)
AI-written · Verified · Written by AI. Only units that passed a separate AI check (re-reading facts and numbers) are published. Tell us if you find a mistake.