CDL Combination Vehicles Concept Review
Based on 2026 exam standards
In the print window, choose 'Save as PDF' as the destination to get a file.
Source: ExamPasso https://exampasso.com/en/cert/cdl-combination-vehicles/concepts
Summary notes
Section 1 ยท CDL Combination Vehicles Test20 questions
1-1. Driving Combination Vehicles Safely
โ โ โ โ โ 25% (estimate)
Overview
A truck that pulls a trailer behaves differently from a single truck. This chapter explains why a combination tips over more easily, why it can be harder to stop when it is empty, and how the trailer moves in turns, skids, and when backing. The test questions usually describe a situation and ask what the trailer will do or what you should do next.
Rollover is the biggest danger. Cargo stacked high moves the center of gravity up, and a heavy load makes a crash rollover far more likely. A quick lane change adds the crack-the-whip effect: the swing grows from the tractor back to the last trailer, so the rear trailer of doubles or triples is the one most likely to go over. The manual names two defenses against rollover: keep the cargo low and drive slowly around turns. It also says to keep the load centered. Against the crack-the-whip effect, steer gently and leave a long gap to the vehicle ahead so you never need a sudden swerve.
Braking and turning have their own traps. A light trailer has poor traction because its springs are stiff and its brakes are strong, so wheels lock and the trailer can slide out of line. A bobtail tractor is also hard to stop smoothly. In turns, the rear wheels cut inside the path of the front wheels, and when backing, the steering works in reverse of what car drivers expect.
Key notes
- Center of gravity
- โ The point where the weight of the rig and its load is balanced. The higher it sits above the road, the easier the rig tips in a turn or a sudden swerve.
- Rearward amplification
- โ The way a quick steering move grows larger at each unit toward the back of the rig. A value of 2.0 means the last trailer is twice as likely as the tractor to turn over.
- Trailer jackknife
- โ A skid in which the trailer wheels lock and the trailer swings out to the side. It happens most with an empty or lightly loaded trailer.
- Bobtail
- โ A tractor driving without a semitrailer. Tests show it can take longer to stop than a tractor-semitrailer loaded to its maximum weight.
- Off-tracking (cheating)
- โ In a turn, the rear wheels follow a tighter path than the front wheels. The longer the rig, the more it happens, and the last trailer's rear wheels cut in the most.
- Button hook turn
- โ The correct way to finish a right turn that needs extra room: keep the rear near the curb and swing wide only as you complete the turn. Swinging left before turning (the jug handle) invites cars to pass on your right.
โ Exam points
- Low, centered cargo and slow turns are the two rollover defenses the manual names.
- Release the brakes in a trailer skid; the locked trailer wheels caused it.
- Back toward the driver's side on a curve so you can see the trailer.
- Low-slung trailers such as lowboys and car carriers can hang up on raised crossings.
1-2. Combination Vehicle Air Brakes
โ โ โ โ โ 30% (estimate)
Overview
A combination vehicle uses the same air brakes as a single truck, plus parts that send air to the trailer and protect the tractor if the trailer loses air. This chapter names those parts, explains what each one does, and shows what happens when a line breaks, leaks, or is connected the wrong way.
Two hoses run from the tractor to the trailer. One fills the trailer's air tanks and keeps the trailer emergency brakes released; the other carries the brake signal from the pedal. In the cab, a red eight-sided knob lets air flow to the trailer and closes the tractor protection valve when you pull it, or by itself when pressure drops very low. Closing that valve keeps the tractor's own air from escaping through a broken trailer line.
Several parts keep the system working safely: couplers called glad hands with rubber seals, dummy couplers that keep dirt out when no trailer is attached, tanks that must be drained daily, and shut-off valves at the back of trailers that tow another trailer. Older trailers and converter dollies may have no spring brakes, so they rely on stored air and must be chocked when parked.
Key notes
- Tractor protection valve
- โ A valve that shuts off air going from the tractor to the trailer. It closes when you pull the trailer air supply knob, or by itself when pressure falls to about 20 to 45 psi, and then the trailer emergency brakes apply.
- Trailer air supply control
- โ The red eight-sided knob in the cab on newer vehicles. Older rigs may use a lever marked normal and emergency, which may not work automatically.
- Service line
- โ The air line that carries the braking signal. Its pressure rises and falls with how hard you press the brake pedal or trailer hand valve, and it goes to relay valves on the trailer. It is often blue.
- Emergency line
- โ The air line that fills the trailer tanks and holds the trailer emergency brakes off. If it loses pressure, the trailer emergency brakes come on and the tractor protection valve closes. It is often red.
- Trailer hand valve
- โ A hand control, also called the trolley valve or Johnson bar, that applies only the trailer brakes. It is for testing those brakes, not for slowing down or parking.
- Shut-off valves
- โ Valves (cut-out cocks) in both air lines at the back of trailers that tow another trailer. They are opened so air passes back and closed at the very end of the rig.
- Crossed air lines
- โ The service hose joined to the emergency glad hand, or the reverse. Air then cannot fill the trailer tanks, so spring brakes stay on; on old trailers without spring brakes you might drive off with no trailer brakes.
โ Exam points
- Using the hand valve while driving can make the trailer skid.
- A major service-line leak often shows up only when you brake.
- Join glad hands with the seals at a right angle, then turn to lock them.
- Trailer air tanks are filled through the emergency line.
1-3. Antilock Brakes on Trailers
โ โ โ โโ 10% (estimate)
Overview
Antilock brakes keep the wheels from locking during hard braking. This chapter covers which trailers and dollies must have them, how to spot them, and how to drive a rig that has ABS on the tractor, the trailer, or both.
Trailers and converter dollies made from March 1, 1998 on must have ABS, and many older ones were fitted with it anyway. A yellow lamp on the left side of the trailer shows an ABS problem. On older units without a lamp, the computer box and the sensor wires behind the brakes tell you ABS is there.
ABS does not add stopping power and does not promise a shorter stop. It steps in only when a wheel is about to lock, which helps you keep steering. You brake the same way as always, and if ABS fails you still have normal brakes.
Key notes
- ABS requirement date
- โ Trailers and converter dollies built on or after March 1, 1998, must be equipped with antilock brakes.
- ABS malfunction lamp
- โ A yellow lamp on the left side of the trailer, at the front or rear corner. Dollies built from the same date need a lamp on the left side too.
- ECU and wheel speed sensors
- โ The electronic control unit and the sensors at the wheels. Seeing the sensor wires coming from the back of the brakes shows that an older trailer has ABS.
- Trailer-only ABS
- โ ABS fitted only on the trailer. It keeps the trailer from swinging out, but if the tractor starts to jackknife you should ease off the brakes, if it is safe, until you regain control.
โ Exam points
- ABS keeps control during hard braking; it does not make you stop shorter.
- Brake the same way whether ABS is on the tractor, the trailer, or both.
- ABS is not a reason to drive faster or follow more closely.
1-4. Coupling and Uncoupling
โ โ โ โ โ 25% (estimate)
Overview
Coupling joins the tractor's fifth wheel to the trailer's kingpin, and uncoupling separates them. Each step has a reason, and mistakes can drop a trailer or let it come loose on the road, so test questions often ask about the order of the steps or why a step is done.
Before coupling, you inspect the fifth wheel and set it ready, hold the trailer still, line the tractor up straight, and touch the trailer gently. You then connect the two air hoses to their matching couplers, fill the trailer with air, listen for crossed lines with the engine off, and set the trailer brakes before backing under to lock onto the kingpin. A gentle pull forward with the trailer brakes on proves the lock.
After the tug test you get out and look: the two plates must sit flat together and the jaws must wrap the narrow middle of the kingpin. Then you plug in the electrical cord, crank the landing gear fully up, and check clearances. Uncoupling runs roughly in reverse, with care for the ground under the trailer, the weight on the landing gear, and your own feet near the tractor wheels.
Key notes
- Fifth wheel
- โ The coupling plate on the tractor with locking jaws that grab the trailer's kingpin. It must be greased, securely mounted, and set with the jaws open before coupling.
- Kingpin
- โ The steel pin under the front of the trailer. It has a base at the top, a narrow shank in the middle, and a wider head at the bottom; the jaws must close around the shank.
- Trailer height
- โ Before backing under, the trailer nose should sit just low enough that the tractor lifts it a little. Too low risks hitting the nose; too high may give a bad coupling.
- Tug test
- โ With the landing gear raised slightly off the ground and the trailer brakes still locked, you pull forward gently to make sure the trailer is locked on.
- Landing gear
- โ The legs that hold up the front of the trailer when it is not coupled. Crank it in low range under load and high range once free, raise it fully before driving, and secure the handle.
- Easing jaw pressure
- โ When uncoupling, you lock the trailer brakes, back gently against the kingpin, and set the parking brakes while pushing. This takes the load off the jaws so the release handle pulls easily.
โ Exam points
- Never back under a trailer at an angle; it can push the trailer sideways and break the landing gear.
- Take the key with you before going under the rig.
- Hang the electrical plug facing down so water stays out.
- Chock the trailer when uncoupling if it lacks spring brakes or you are not sure.
1-5. Inspecting a Combination Vehicle
โ โ โ โ โ 10% (estimate)
Overview
A combination is inspected with the same seven-step method as any commercial vehicle, plus checks for parts a single truck does not have. This chapter lists those extra walk-around items and explains the four brake tests for a combination, which apply to doubles and triples too.
On the walk-around you look at both halves of the coupling, the air hoses and electrical cord, any sliding fifth wheel, and the landing gear. Most items ask whether a part is secure, undamaged, greased, or fully raised, and whether hoses have enough slack for turns.
The brake tests prove that air reaches the back of the rig, that the tractor protection valve closes on its own when pressure falls, and that both the trailer emergency brakes and service brakes work. Each test uses a different control, and questions often swap one test's method into another.
Key notes
- Air-to-all-trailers test
- โ With normal pressure and the red knob pushed in, you go to the very back and open the emergency valve, then the service valve with the brakes applied, listening for air from each. If no air comes out, first check that the shut-off valves on the trailers and dollies are open.
- Tractor protection valve test
- โ With the system charged and the engine off, you press and release the brake pedal several times to lower the pressure. The trailer air supply knob should pop out in the range the maker sets, usually 20 to 45 psi.
- Trailer emergency brake test
- โ After checking that the charged trailer rolls freely, you pull out the trailer air supply knob and tug gently with the tractor to feel the trailer brakes hold.
- Trailer service brake test
- โ With normal pressure and the parking brakes released, you roll forward slowly and apply the trailer brakes with the hand valve, if there is one. In normal driving the foot pedal controls them.
- Sliding fifth wheel
- โ A fifth wheel that can move along the frame. Its locking pins must all be present and locked, and it must not sit so far forward that the frame hits the landing gear or the cab hits the trailer in a turn.
โ Exam points
- Jaws around the head instead of the shank mean a bad coupling.
- Air and electrical lines need slack for turns but must be secured.
- Doubles and triples get the same brake checks as any combination.
Multiple choice questions on the Combination Vehicles section of your state's CDL manual (Section 6 in the common manual layout) ยท 1 sections ยท 20 questions ยท 25 min
Pass: 80 points average
Source: State driver licensing agencies (DMV) ยท as of 2026
AI-written ยท Verified ยท Written by AI. Only units that passed a separate AI check (re-reading facts and numbers) are published. Tell us if you find a mistake.